- LL FILM
LL Film has excellent gloss and drawdown properties. It is without slip and anti-blocking agent additives. It is especially used in the production of the stretch film by cast process and is also used in a blend with LDPE for light-duty blown film applications.
Data Grade Sheet
F18A010U Linear Low-Density Polyethylene Film
Product Description and Typical Applications:
F18A010U has excellent processability with an optimum balance of mechanical and optical properties. It
is without slip and anti-blocking agent additive.
It is widely used for lamination and cling film applications.
| Property | Values* | Unit | Test Method |
| Melt Flow Index (I2 ) |
1.0 | g/10min | ASTM D1238 |
| Density | 0.918 | g/cc | ASTM D1505 |
| Tensile Strength @Break (MD/TD) | 410/290 | kg/cm2 | ASTM D882 |
| Elongation @Break (MD/TD) | 580/680 | % | ASTM D882 |
| Tear Strength (MD/TD) | 6/15 | g/ mic | ASTM D1922 |
| Dart Impact Strength | 3.7 | g/ mic | ASTM D1709 |
* Typical characteristics of the product given purely as a guide. Film properties were measured on 25.4 microns blown film extruded at a blow-up ratio (BUR)
2.5.
Processing Guidelines:
Barrel temperature: 180 – 2200C
Blow up ratio: 2.0 to 3.0
Regulatory Information:
The certificate is available on request.
Packaging & Storage:
F18A010U is available in natural color/pellet form in 25 kg strong bags made of woven fabric. The product should be stored in dry conditions at a temperature below 50oC and protected from UV light.
F18A020U Linear Low-Density Polyethylene Film
Product Description and Typical Applications:
F18A020U has excellent gloss and drawdown properties. It is without slip and anti-blocking agent additives. It is especially used in the production of the stretch film by cast process and is also used in a blend with LDPE for light-duty blown film applications.
| Property | Values* | Unit | Test Method |
| Melt Flow Index (I2 ) | 2 | g/10min | ASTM D1238 |
| Density | 0.918 | g/cc | ASTM D1505 |
| Tensile Strength @Break (MD/TD) | 350/250 | kg/cm2 | ASTM D882 |
| Elongation @Break (MD/TD) | 450/850 | % | ASTM D882 |
| Tear Strength (MD/TD) | 10-Feb | g/mic | ASTM D1922 |
| Dart Impact Strength | 2.8 | g/mic | ASTM D1709 |
* Typical characteristics of the product given purely as a guide. Film properties were measured on 25-micron cast film extruded at 270 °C.
Processing Guidelines:
Cast Film:
Processing temperature: 2600C – 280°C
Blown Film
Barrel temperature: 180 – 2200C
Blow up ratio: 2.0 to 3.0
Regulatory Information:
The certificate is available on request.
Packaging & Storage:
F18A020U is available in natural color/pellet form in 25 kg strong bags made of woven fabric. The product should be stored in dry conditions at a temperature below 50oC and protected from UV light.
F18S020U Linear Low-Density Polyethylene Film
Product Description and Typical Applications:
F18S020U has excellent gloss and drawdown properties. It has an adequate level of slip and anti-blocking agent additives. It is recommended for use in liners, industrial packaging, and other general
purpose film applications.
| Property | Values* | Unit | Test Method |
| Melt Flow Index (I2 ) | 2 | g/10min | ASTM D1238 |
| Density | 0.918 | g/cc | ASTM D1505 |
| Tensile Strength @Break (MD/TD) | 300/230 | kg/cm2 | ASTM D882 |
| Elongation @Break (MD/TD) | 650/760 | % | ASTM D882 |
| Tear Strength (MD/TD) | 2/10 | g/ mic | ASTM D1922 |
| Dart Impact Strength | 2.7 | g/ mic | ASTM D1709 |
* Typical characteristics of the product given purely as a guide. Film properties were measured on 25.4 microns blown film extruded at a blow-up ratio (BUR)2.5.
Processing Guidelines:
Barrel temperature: 180 – 2200C
Blow up ratio: 2.0 to 3.0
Regulatory Information:
The certificate is available on request.
Packaging & Storage:
F18S020U is available in natural color/pellet form in 25 kg strong bags made of woven fabric. The product should be stored in dry conditions at a temperature below 50oC and protected from UV light.
Linear Low Density Polyethylene Packaging Films
Product Description:
LLDPE F2001S is a butene co-monomer based natural colored grade produced with the latest Ineos Gas Phase polymerization Technology exhibiting following features:
¸ Excellent Mechanical Properties
¸ Very Good optical properties
¸ Easy Processing
¸ With Slip & Anti-block additives
LLDPE F2001S is recommended for following applications:
¸ Co-extrusion films
¸ Liquid Packaging films
¸ Drip laterals
¸ Agriculture Films
Typical Properties:
| Tested Properties | Test Method | UOM | Value |
| Melt Flow Index ( 190o C & 2.16 kg) | ASTM D 1238 | gm/10 min | 0.9 |
| Density @ 23oC | ASTM D 1505 | gm/cm3 | 0.919 |
| Mechanical Properties | |||
| Tensile Strength @ Yield (50 mm/min) | ASTM D882 | MPa | 11.0/12.0 |
| Tensile Strength @ Break (50mm / min) (MD/TD) | ASTM D882 | MPa | 44.0/40.0 |
| Elongation @ Break (50mm / min) (MD/TD) | ASTM D882 | % | 600/800 |
| Dart Impact Strength, F50 (38mm dart, 66cm height) | ASTM D1709 | g/µm | 3.5 |
| Tear Strength (MD/TD) | ASTM D1922 | g/µm | 3.5/10.0 |
| Coefficient of Friction (Static/Dynamic) | ASTM D1894 | – | 0.23/0.16 |
| Film Gloss (600 ) | ASTM D523 | % | 70 |
* Mechanical Properties tested on 40 µ (microns) thick monolayer blown film made with 1.8 mm die gap and 2.25 BUR.
* Typical Values and not to be taken as specification limits, values may change without any prior notice.
Recommended Processing Temperature: 170 – 210 0C
Regulatory Requirements:
LLDPE film grade F2001S shall meet the requirements stipulated in IS 10146:1982 on ‘Specification of Polyethylene for safe use in contact with Foodstuff, Pharmaceutical & Drinking water’. The grade and Additives incorporated in this grade shall meet the positive list of constituents as prescribed in IS 10141:1982. The Grade and the additives incorporated in it shall also
comply with the FDA: CFR Title 21,177.1520, Olefin Polymers.
Storage & Handling:
Prevent Polyethylene Material from direct exposure to sunlight & heat to avoid quality deterioration. The storage location should be dry, dust free and the Storage temperature should not exceed 50 o C. Non – compliance to these precautionary measures can lead to degradation of the product causing Color changes, Odor & inadequate product performance.
Health and Safety Information:
The product described herein may require precautions in handling and use because of toxicity, flammability, or other consideration. The Material Safety Data Sheet (MSDS) contains the available product health and safety informtion for this
material and can be found at www.opalindia.in. Before using any material, a customer is advised to consult the MSDS for the product under consideration for use.
Linear Low Density Polyethylene Packaging Films
Product Description:
LLDPE F2001A is a butene co-monomer based natural colored grade produced with the latest Ineos Gas Phase polymerization Technology exhibiting following features:
¸ Excellent Mechanical Properties
¸ Very Good optical properties
¸ Easy Processing
¸ Without Slip & Anti-block additives
LLDPE F2001A is recommended for following applications:
¸ Co-extrusion films
¸ Lamination films
¸ Drip laterals
¸ Agriculture Films
Typical Properties:
| Tested Properties | Test Method | UOM | Value |
| Melt Flow Index ( 190o C & 2.16 kg) | ASTM D 1238 | gm/10 min | 0.9 |
| Density @ 23oC | ASTM D 1505 | gm/cm3 | 0.918 |
| Mechanical Properties | |||
| Tensile Strength @ Yield (50 mm/min) | ASTM D882 | MPa | 11.0/12.0 |
| Tensile Strength @ Break (50mm / min) (MD/TD) | ASTM D882 | MPa | 44.0/40.0 |
| Elongation @ Break (50mm / min) (MD/TD) | ASTM D882 | % | 600/800 |
| Dart Impact Strength, F50 (38mm dart, 66cm height) | ASTM D1709 | g/µm | 3.5 |
| Tear Strength (MD/TD) | ASTM D1922 | g/µm | 3.5/10.3 |
* Mechanical Properties tested on 40 µ (microns) thick monolayer blown film made with 1.8 mm die gap and 2.25 BUR.
* Typical Values and not to be taken as specification limits, values may change without any prior notice.
Recommended Processing Temperature: 170 – 210 0C.
Regulatory Requirements:
LLDPE film grade F2001A shall meet the requirements stipulated in IS 10146:1982 on ‘Specification of Polyethylene for safe use in contact with Foodstuff, Pharmaceutical & Drinking water’. The grade and Additives incorporated in this grade shall meet the positive list of constituents as prescribed in IS 10141:1982. The Grade and the additives incorporated in it shall also
comply with the FDA: CFR Title 21,177.1520, Olefin Polymers.
Storage & Handling:
Prevent PE Material from direct exposure to sunlight & heat to avoid quality deterioration. The storage location should be dry, dust free and the Storage temperature should not exceed 50 oC. Non – compliance to these precautionary measures can lead to degradation of the product causing Color changes, Odor & inadequate product performance.
Health and Safety Information:
The product described herein may require precautions in handling and use because of toxicity, flammability, or other consideration. The Material Safety Data Sheet (MSDS) contains the available product health and safety information for this material and can be found at www.opalindia.in. Before using any material, a customer is advised to consult the MSDS for the product under consideration for use.
F18S010U
Linear Low-Density Polyethylene Film
Product Description and Typical Applications:
F18S010U is a Linear low-density polyethylene (LLDPE) resin for blown film extrusion offering excellent processability with an optimum balance of mechanical and optical properties. It has an adequate level of slip and anti-blocking agent for good operability and slips characteristics of the film. It offers excellent drawdown capability for thinner gauge films. Its low gel count, resistance to leakage & pinholes, excellent sealing characteristics make it preferred choice for consumers in Industrial/ consumer packaging for various applications.
It is recommended for general purpose, heavy duty and liquid packaging in laminated/ non-laminated blown film applications.
| Property | Values* | Unit | Test Method |
| Melt Flow Index (I2) | 1.0 | g/10min | ASTM D1238 |
| Density | 0.918 | g/cc | ASTM D1505 |
| Tensile Strength @Break (MD/TD) | 400/270 | kg/cm2 | ASTM D882 |
| Elongation @Break (MD/TD) | 580/750 | % | ASTM D882 |
| Tear Strength (MD/TD) | 6/15 | g/ mic | ASTM D1922 |
| Dart Impact Strength | 3.0 | g/mic | ASTM D1709 |
* Typical characteristics of the product given purely as a guide. Film properties were measured on 25.4 micron blown film extruded at a blow up ratio (BUR) 2.5.
Processing Guidelines:
Barrel temperature: 180 – 2200C Blow up ratio: 2.0 to 3.0
Regulatory Information:
Certificate is available on request.
Packaging & Storage:
F18S010U is available in natural colour/pellet form in 25 kg strong bags made of woven fabric. The product should be stored in dry conditions at temperature below 50oC and protected from UV light.
F20S009
Linear Low-Density Polyethylene for Blown Film Extrusion
Application: F20S009 is optically stabilized with antioxidants, slip additives, anti-blocking agents, and a processing aid.
It has excellent processability with an optimum combination of mechanical, optical, and sealing characteristics. It is recommended for general-purpose, heavy-duty, and liquid packaging in laminated / non-laminated film applicationS.
| Property | Values* | Unit | Test Method | |
| Melt Flow Index (I2) | 0.9 | gm/10min | ASTM D1238 | |
| Density | 0.918 | gm/cc | ASTM D1505 | |
| Tensile Strength @Break (MD/TD) | 390/310 | kg/cm2 | ASTM D882 | |
| Elongation @Break (MD/TD) | 700/800 | % | ASTM D882 | |
| Tear Strength (MD/TD) | 3.0/10 | gm/mic | ASTM D1922 | |
| Dart Impact Strength | 3.4 | gm/mic | ASTM D1709 | |
| Coefficient of Friction (Static/Dynamic) | 0.22/0.17 | ASTM D1894 | ||
| Haze | 9 | % | ASTM D1003 | |
* Typical characteristics of the product given purely as a guide. Mechanical/Optical properties were determined on 40-micron film made with a 2.0mm die gap and BUR: 2.2
Processing Guidelines:
Barrel temperature: 170 – 2000C Blow up ratio: 2.0 to 2.25
Die gap: 1.8 to 2.2
Regulatory Information: The certificate is available on request.
Packaging & Storage:
F20S009 is available in natural color/pellet form in 25 kg strong bags made of woven fabric. The product should be stored in dry conditions at a temperature below 50oC and protected from UV light.
